|
Still deciding? Get samples of $ !
Request Sample
|
| Customization: | Available |
|---|---|
| Application: | Valve |
| Type: | Oil Seal |
| Shipping Cost: | Contact the supplier about freight and estimated delivery time. |
|---|
Suppliers with verified business licenses
Audited by an independent third-party inspection agency
This page covers the 6A wellhead range of ring joint gaskets: the RX and BX styles used on 6A flanges, wellheads, Christmas trees and blowout preventer stacks, made to ASME B16.20 and machined from forged rings rather than from rolled bar.
Forging matters here. A BX ring is a square section pressed into a square groove at high pressure, and a ring with a lap or a seam can open along it. The rings we supply are forged, then machined, then stamped with the size, the style and the heat number.

└ Ring joint gasket in the BX style, coated for storage and marked on the face.
| Item | Value |
|---|---|
| Standard | ASME B16.20; 6A flanges for the wellhead range |
| Styles | RX and BX; R oval and R octagonal also supplied |
| Pressure | Up to 20,000 psi for BX in the appropriate flange |
| Material | Soft iron, low carbon steel, SS304, SS316L, F5 |
| Manufacture | Forged ring, machined, stamped with size, style and heat number |
| Hardness | Checked against the groove requirement, recorded on the certificate |
| Coating | Rust preventive coating for storage; no paint on the sealing face |
| Reuse | BX once if undeformed; R and RX not reusable |
The RX ring has a pressure balance hole drilled through the section. Line pressure passes through it and acts on the inner face, so the seal tightens as the pressure rises instead of being pushed apart. The RX ring seats in a groove with a steeper wall than the R style and is used from Class 900 upward.
The BX ring is a square section in a square groove. It is the highest pressure design and the one used on 6A wellhead equipment. Because the groove and the ring are both flat faced, the ring deforms into the groove corners and a used ring must be checked for flatness before it is considered for reuse.
![]() |
![]() |
![]() |
└ Left: RX section with the pressure balance hole. Centre: BX square section. Right: R style ring for comparison.

└ Octagonal ring gaskets after machining, stacked before marking. The octagonal section is the R style alternative to the oval section; both seat in the same groove.
![]() |
![]() |
└ Left: ring section close up, the tapered face that seats in the groove. Right: two rings standing side by side with the section outline showing.
Soft iron is the default for wellhead service; low carbon steel where a harder ring is asked for; 316L where the produced fluid is sour or chloride bearing. The ring must be softer than the flange groove, or the groove deforms instead of the ring and the flange has to be replaced.
| Material | Typical service |
|---|---|
| Soft iron | Wellhead and general 6A service, the default |
| Low carbon steel | High pressure process and steam flanges |
| SS304 | Corrosive service, moderate chloride |
| SS316L | Sour and chloride bearing produced fluid |
| F5 | High temperature steam and hydrogen service |

└ Ring after machining: the sealing face is ground flat and carries no paint.
The groove is cleaned and inspected before every make up. The ring goes in dry, centred by hand, and the flanges are brought together without forcing. Bolts are tightened in a star pattern in three passes to the torque in the flange standard; on a wellhead the torque is the one in the equipment manual, not a generic table.
A ring that has been in service is not put back into a different groove. On a BX joint the ring may be reused once in the same groove if the faces are still flat and the height is within tolerance, and that is checked with a straight edge before it goes back in.
The quality management system is certified to GB/T 19001-2016 / ISO 9001:2015 by Zhongkai International, certificate ZKP04UKP064108, valid from 28 April 2024 to 27 April 2027.

└ ISO 9001 certificate ZKP04UKP064108, Zhongkai International, valid to 27 April 2027. A management system certificate is not a product certificate and does not replace the mill certificate for the heat.
Rings are packed one per plastic sleeve with the style, size, material and heat number on the label, then set into a plywood case with the rings held flat so the sealing faces do not touch each other. A case of large diameter rings is lined with foam and banded; a mixed order is packed by style so the packing list matches what is in each case.
![]() |
![]() |
└ Left: four rings wrapped and set into a plywood case, held flat so the sealing faces do not touch. Right: rings in their individual plastic sleeves.
| Question | Answer |
|---|---|
| What is the difference between RX and BX? | RX has a pressure balance hole and seats in a groove with a steep wall, used from Class 900 up. BX is a square section in a square groove for the highest pressures, and it is the wellhead design. |
| Can a BX ring be reused? | Once, in the same groove, if it is undeformed and the height is still within tolerance. R and RX rings are not reused. |
| Which material for sour service? | 316L is the usual choice, with the hardness checked against the requirement. Soft iron is not used where the produced fluid is sour. |
| What is the minimum order quantity? | One piece for the size shown. Rings are machined to the style and class ordered. |
| What is the lead time? | 7 to 35 days from confirmation of the order, depending on size, material and quantity. |
Dimensions follow ASME B16.20 and the 6A flange standard. The certificate for the lot states the material and the hardness actually supplied.
Xiamen Qishine Industry Co., Ltd. has supplied piping and sealing components since 2013. The range covers gaskets, fasteners, flanges, fittings, valves, pipes and piping spare parts, supplied mainly to oil and gas, petroleum, marine, oilfield, mining and heavy industrial projects, with pipeline construction and maintenance as the main focus.
Most of our work is for EPC contractors and project owners. We quote against the piping class or datasheet you send, produce to the nominated standard, inspect before packing, and ship with mill and inspection certificates.

└ Works and office, Huli District, Xiamen.
Send the standard, size, pressure class and medium, and we will confirm the grade and the lead time.