|
Still deciding? Get samples of $ !
Order Sample
|
| Customization: | Available |
|---|---|
| Material: | Carbon Steel |
| Type: | Round Head |
| Shipping Cost: | Contact the supplier about freight and estimated delivery time. |
|---|
Suppliers with verified business licenses
Audited by an independent third-party inspection agency
A flange stud is a fully threaded bar with a chamfer at each end, used with two heavy hex nuts to close a bolted flange joint. The thread runs the full length, so the stud can be turned either way and the nut never runs out of thread inside the flange thickness.
This item is ASTM A193 grade B7 stud with ASTM A194 grade 2H heavy hex nuts, made to ASME B18.31.2 for the stud and ASME B18.2.2 for the nut. B7 / 2H is the standard pairing for carbon steel and moderate temperature service, and it covers most oil, gas, water and steam piping classes.
A stud is measured parallel to its axis, from the first full thread at one end to the first full thread at the other, excluding the chamfers. That dimension is what has to match the flange thickness plus two nuts plus two washers. A hex bolt is measured differently, from under the head to the tip, which is why a drawing that mixes the two conventions produces the wrong length.

└ Stud length runs thread to thread without chamfers; a hex bolt is measured under the head
Give the stud length as thread-to-thread. If the drawing gives the length under the head, say so, because the two dimensions differ by the chamfer and the head height.
Stud and nut are always ordered as a pair. The grades below are the standard combinations; the service condition decides which one, not the size.
| Service | Stud | Nut | Used for |
|---|---|---|---|
| Carbon steel, moderate temperature | A193 B7 | A194 2H | Oil, gas, water and steam piping classes |
| Carbon steel, higher strength | A193 B7M | A194 2HM | Heavy wall and high pressure joints |
| Low temperature | A320 L7, L7M | A194 Gr.4, Gr.7 | Cold service, LNG and refrigeration |
| Stainless, corrosion resistant | A193 B8, B8M | A194 8, 8M | Process, marine and chemical service |
| Chromium molybdenum, elevated temperature | A193 B16 | A194 Gr.7 | Steam and hydrogen service |
| High temperature alloy | A453 Gr.660 | A453 Gr.660 | Turbine and high temperature flanges |
The nut is specified 30 to 50 HB softer than the stud. That gap is what makes the nut take the wear when a joint is made up again, instead of the stud thread.
| Element | B7 (AISI 4140) | B8 (AISI 304) | B8M (AISI 316) |
|---|---|---|---|
| Carbon | 0.38 - 0.48 % | 0.08 % max | 0.08 % max |
| Manganese | 0.75 - 1.00 % | 2.00 % max | 2.00 % max |
| Phosphorus | 0.035 % max | 0.045 % max | 0.045 % max |
| Sulfur | 0.040 % max | 0.030 % max | 0.030 % max |
| Silicon | 0.15 - 0.35 % | 1.00 % max | 1.00 % max |
| Chromium | 0.80 - 1.10 % | 18.0 - 20.0 % | 16.0 - 18.0 % |
| Nickel | - | 8.0 - 11.0 % | 10.0 - 14.0 % |
| Molybdenum | 0.15 - 0.25 % | - | 2.00 - 3.00 % |
| Grade | Size (inch) | Tensile min (KSI) | Yield min (KSI) | Elongation % | Max hardness |
|---|---|---|---|---|---|
| B7 | Up to 2-1/2 | 125 | 105 | 16 | 321 HBW / 35 HRC |
| B7 | 2-5/8 - 4 | 115 | 95 | 16 | 321 HBW / 35 HRC |
| B7 | 4-1/8 - 7 | 100 | 75 | 18 | 321 HBW / 35 HRC |
| B8 Class 1 | All | 75 | 30 | 30 | 223 HBW / 35 HRC |
| B8M Class 1 | All | 75 | 30 | 30 | 223 HBW / 96 HRC |
| B8 Class 2 | Up to 3/4 | 125 | 100 | 12 | 321 HBW / 35 HRC |
| B8M Class 2 | Up to 3/4 | 110 | 95 | 15 | 321 HBW / 35 HRC |
Class 2 stainless is strain hardened and is not available in every diameter. State the class on the order, because Class 1 and Class 2 have the same grade name and different strength.
The coating decides how long the fastener survives in the atmosphere, not how strong it is. For flange bolting the four common finishes are:
Coated studs are matched with the same coating on the nuts and washers. A bare nut on a coated stud loses the coating at the first make-up.
Threads are checked with go and no-go gauges (2A fit for inch threads), diameter and length with calipers, and hardness on the finished part. Mechanical properties are verified against the grade on the material test certificate. A certificate to EN 10204 3.1 with heat number is issued for each lot, and third party inspection by SGS, TUV, BV or the buyer's inspector can be arranged before packing.

└ Thread gauging, dimensional check and packing inspection before dispatch

└ ISO 9001:2015 certificate ZKP090UFQ64108, issued by Zhongkai International Certification Services (China) Co., Ltd., valid to 27 April 2027
One joint rarely needs only the studs. The same piping class calls for the flange pair, the gasket between them and often the fittings on either side. We supply those items from the same stock, so bolt holes, gasket bore and flange facing are checked against each other before the crate is closed.
Sizes and grades follow the piping class you send. Give the class and the line size and the matched set is quoted as one lot, with the stud length and nut grade already fixed for the flange thickness you are using.
└ Left: sleeves, spiral wound gaskets, coated studs, nuts and tube. Right: G10 kits, square and copper tube, flanges and forged fittings from the same stock.
Studs are packed in bundles by diameter and length, with the heat number on the label; nuts are boxed separately per joint so the count matches the studs. Standard sizes ship in 7 to 35 days from confirmation of grade, diameter, length, coating and quantity.
Flange bolting is a piping item, so the applications follow the piping classes we quote against: oil and gas gathering and transmission, refinery and petrochemical units, power plant steam and cooling water, marine and offshore topsides, water treatment and pulp and paper.

└ Industries served by the piping and sealing range
| Question | Answer |
|---|---|
| What is the minimum order? | Ten kilograms for standard sizes, with 100 kg and 1000 kg order tiers. Larger quantities are quoted against the size list. |
| How long does delivery take? | 7 to 35 days from confirmation of grade, diameter, length, coating and quantity. |
| Do the nuts come with the studs? | Yes. The quotation is normally for one stud with two 2H nuts, and washers are added where the piping class calls for them. |
| Which length do I order? | The thread-to-thread length, which equals flange thickness plus two nuts and two washers plus a few threads showing at each end. |
| Can you supply B8M Class 2 instead of B7? | Yes. Stainless grades are supplied in Class 1 or Class 2, and the class is stated on the certificate. |
| What documents are supplied? | Material test certificate to EN 10204 3.1 with heat number, dimensional and hardness records for the lot, third party inspection on request. |
Send grade, diameter, thread (UNC or 8UN), length, coating and quantity for a firm price and lead time.
Xiamen Qishine Industry Co., Ltd. has supplied piping and sealing components since 2013: fasteners, gaskets, flanges, fittings, valves and piping spare parts for oil and gas, marine, oilfield and heavy industrial projects. Most of our work is for EPC contractors, quoted against the piping class they send, produced to the nominated standard and shipped with mill certificates.
└ Left: factory site, workshops and office at the main gate. Right: reference logos from projects supplied.
The company operates an ISO 9001 certified quality management system.