|
Still deciding? Get samples of $ !
Order Sample
|
| Customization: | Available |
|---|---|
| Material: | Stainless Steel |
| Type: | Round Head |
| Shipping Cost: | Contact the supplier about freight and estimated delivery time. |
|---|
Suppliers with verified business licenses
Audited by an independent third-party inspection agency
Incoloy 901 is a precipitation hardened iron-nickel-chromium superalloy, UNS N09901, also sold as Nimonic 901 and Alloy 901, W.Nr. 2.4662. It holds its yield strength to about 650 °C and resists oxidation to 760 °C, which places it where A193 B16 runs out of creep strength and a stainless bolt would relax: reformer and cracker flanges, hydrogen and FCC units, high temperature steam, and gas turbine casings.
Studs are full thread to ASME B18.31.2, supplied with two heavy hex nuts of the same grade. Matching the nut to the stud matters more here than on carbon steel: the two parts have to expand together through a heat cycle, and a mixed pair will either seize on the thread or lose preload.
| Item | Value |
|---|---|
| Grade | Incoloy 901 / UNS N09901 / W.Nr. 2.4662 |
| Product | Full thread stud bolt with two heavy hex nuts |
| Size | 1/2 to 4 Inch |
| Length | 30 to 800 mm |
| Thread | UNC, 8UN, UNF; metric coarse on request |
| Standards | ASME B18.31.2 (stud), ASME B18.2.2 (nut), ANSI / DIN / NF dimensions |
| Condition | Solution treated and aged |
| Service temperature | 650 °C continuous; oxidation limit 760 °C |
| Finish | Plain, Xylan 1070, PTFE, phosphated |
| Packing | Plywood case |
| Element | Composition (%) |
|---|---|
| Ni | 40.0 - 45.0 |
| Cr | 11.0 - 14.0 |
| Mo | 5.0 - 7.0 |
| Ti | 2.35 - 3.10 |
| Al | 0.35 max |
| C | 0.10 max |
| Mn | 1.00 max |
| Si | 0.60 max |
| Cu | 0.50 max |
| Co | 1.00 max |
| B | 0.01 - 0.02 |
| P | 0.03 max |
| S | 0.03 max |
| Fe | Balance |
Titanium and aluminium form the gamma prime phase that carries the strength; the 5 to 7 percent molybdenum is what separates 901 from A286 at temperature.
| Property | Value |
|---|---|
| Tensile strength, Rm | 1,034 MPa |
| Yield strength, Rp0.2 | 689 MPa |
| Elongation, A5 | 12 % |
| Hardness, aged | about 331 HB |
| Condition | Solution treated and aged |
Minimum room temperature values for the aged condition. Heat specific results are reported on the mill certificate; elevated temperature tensile and stress rupture tests can be added to the order.
| Grade | Service | Typical strength | Position |
|---|---|---|---|
| A193 B7 | to about 450 °C | 860 / 724 MPa | The default refinery bolting; loses strength and creeps above 450 °C |
| A193 B16 | to about 540 °C | about 860 / 690 MPa | Cr-Mo-V grade with better relaxation resistance than B7 |
| Incoloy 901 | to about 650 °C | 1,034 / 689 MPa | Highest creep strength of the three; molybdenum bearing, for heavy sections and hot flanges |
| A453 Gr.660 (A286) | to about 650 °C | 895 MPa min | Chosen where the expansion has to match a stainless flange |
The practical split: on a stainless or high alloy flange, 660 usually wins because its expansion matches the flange. On a heavy steel flange at 600 °C and above, where the joint is load controlled rather than movement controlled, 901 is the stronger choice.
| Control point | Requirement |
|---|---|
| Nut grade | Same grade as the stud, or a grade approved for the same temperature |
| Hardness | Nut controlled below the stud where the specification calls for it, to limit galling |
| Thread | Nut matched to the stud thread series and class; 2A on the stud |
| Set content | One stud plus two heavy hex nuts per bolt position |
| Washers | F436 hardened washer where the joint detail specifies one |
Austenitic and superalloy threads gall when assembled dry. Use a nickel or MoS2 based anti-seize on the thread and under the nut, and do not run the nut down with a high speed impact wrench.
A complete line for quotation reads:
Stud bolt, Incoloy 901 (UNS N09901), 1-1/8 Inch - 8UN x 250 mm, ASME B18.31.2, solution treated and aged, with 2 heavy hex nuts, EN 10204 3.1
Mill certificate to EN 10204 3.1 with heat number, chemical analysis and mechanical results; hardness report for the nuts; dimensional report; third party inspection on request.
Short answers to what buyers ask before the first order. Anything not covered here is answered with the quotation.
| Question | Answer |
|---|---|
| What is the minimum order? | Ten kilograms for standard sizes; non-standard lengths are quoted from drawing. |
| How long does delivery take? | 7 to 35 days from confirmation of size, grade, finish and quantity. |
| Are the nuts supplied with the studs? | Yes. Nuts are matched to the studs and hardness is reported per heat. |
| Which finishes are available? | Plain, Xylan 1070, PTFE or phosphated. |
| What documents are supplied? | Mill certificate to EN 10204 3.1 with heat number, chemical and mechanical results, nut hardness report. |
| Can you produce a non-standard length? | Yes, to drawing, in 8UN, UNC or metric coarse thread. |
└ Send size, grade, quantity and destination port with your enquiry for a firm price and lead time.
Xiamen Qishine Industry Co., Ltd. has supplied piping and sealing components since 2013. The range covers gaskets, fasteners, flanges, fittings, valves, pipes and piping spare parts, supplied mainly to oil and gas, petroleum, marine, oilfield, mining and heavy industrial projects, with pipeline construction and maintenance as the main focus.
Most of our work is for EPC contractors and project owners. We quote against the piping class or datasheet you send, produce to the nominated standard, inspect before packing, and ship with mill and inspection certificates. Where one joint needs several items - gasket, studs, nuts, washers - they are supplied as one matched set, so thread fit and hardness pairing are already checked when the crate is opened.
Send the standard, size, pressure class and medium, and we will confirm the grade and the lead time.
The company operates an ISO 9001 certified quality management system, and the certificate is shown above.